UTILIZATION AND ENGINEERING OF PISTON WASTE BY SHOT PEENING METHOD AS ALTERNATIVE MATERIAL FOR FISHING VESSEL PROPELLERS

Bambang Hari Priyambodo; Rizqi ilmal Yaqin; Rauuf Nur Fattah; Sugeng Slamet

doi:10.15578/aj.v6i2.14967

UTILIZATION AND ENGINEERING OF PISTON WASTE BY SHOT PEENING METHOD AS ALTERNATIVE MATERIAL FOR FISHING VESSEL PROPELLERS

Bambang Hari Priyambodo, Rizqi ilmal Yaqin, Rauuf Nur Fattah, Sugeng Slamet

Abstract

This study aims to evaluate the utilization of used piston waste as an alternative material for making fishing boat propellers. Engineering is carried out to improve its mechanical properties by shot peening treatment. Shot peening is a surface treatment method by shooting small steel ball particles in a controlled manner. In this study, used pistons were recycled and used as the basic material for propellers, then shot peening was carried out with a pressure of 8 bar with variations in shooting duration for 5, 10, 15, and 20 minutes. Testing includes testing the chemical composition of the specimen, tensile testing, and observing the micro structure. Tensile testing is to determine mechanical strength, while macro photography is to identify changes in surface structure. The results of the chemical composition test state that the recycled piston is AL-Si-Cu. Meanwhile, the results of the tensile test show that the longer the shot peening duration, the tensile strength of the material increases significantly. Shot peening with a duration of 20 minutes gives the highest strength. The increase in tensile strength is 43% or 113 MPa compared to the non-treatment specimen. Micro structure observations show that the shot peening process creates a denser surface layer, so that tensile strength can be increased. This research is expected to be a reference for the propeller industry to increase production efficiency and sustainability.

Keywords

Piston waste, propeller, shot peening.

Full Text:

PDF

References

Chen, H., Liu, X., Wang, Y., & Zhang, S. (2022). Effect of Short Duration Shot peening on Mechanical Properties and Microstructure of Aluminum Alloys. Materials Science and Engineering A, 815, 141306.

Kumar, R., Singh, V., & Kalsi, N. S. (2020). Influence of Shot peening Duration on Surface Integrity and Mechanical Properties of Aluminum Alloys. International Journal of Surface Engineering and Materials Technology, 10(2), 98-105.

Li, J., Liu, S., Zhang, X., Wang, Y. (2019). Effect of Shot peening on the Microstructure and Mechanical Properties of High-Strength Steel. Journal of Materials Science & Technology, 35(7), 1189-1197.

Liu, X., Zhao, Y., & Feng, P. (2023). Influence of Shot peening Duration on Tensile Strength and Microstructure of Alloy Materials. Journal of Mechanical Engineering Research, 47(2), 152-165.

Margono, M., Pasmawati, Y., Atmoko, N. T., Yaqin, R. I., Priyambodo, B. H. (2023). Perbaikan Kekerasan dan Struktur Mikro Logam Kuningan sebagai Bahan Propeller dengan Metode Shot peening. JTT (Jurnal Teknologi Terapan) 9 (2), 120-127.

Mina T., Manuel, V., Carlos, G. S., (2022). Towards Fuel Consumption Reduction Based on the Optimum Contra-Rotating Propeller. Journal of Marine Science and Engineering, 10(11):1657.

Mohammad, A. J., & Abi, P. (2024). Interaction Analysis Hull And Propeller And Improvement Of Efficiency Propeller On Fishing Vessels. International Journal Of Marine Engineering And Applications, Vol. 1 No. 1.

Peng, Q., Zhou, X., Liu, J. (2020). Analysis of Over-Peening Effects on Fatigue Performance of Aluminum Alloys. International Journal of Fatigue, 141, 105884.

Pratama, H. (2018). Mechanical Properties of Recycled Piston Materials for Marine Propellers. Materials Science Journal, 12(2), 89-95.

Priyambodo, B. H. & Slamet, S. (2020). Increased Corrosion Resistance On Cu35% Zn Surface By Shot peening Process. Journal Of Physics: Conference Series 1430 (1), 012055.

Priyambodo, B. H., Margono, M., Atmoko, N. T., Suhartoyo, Yaqin, R. I. (2024). Improvement Of Hardness And Micro Structure Of Cu-Zn As A Propeller Material By Shot peening Method. AIP Conference Proceedings 2952 (1).

Setiawan, D. (2016). Recycling Piston Scrap for Efficient Boat Propeller Production: A Cost-Effective Solution for Small-Scale Fisheries. Journal of Mechanical Engineering and Technology, 5(3), 140-149.

Slamet, S., Priyambodo, B. H., Suhartoyo, Yaqin, R. I. (2018). Pengaruh Durasi Waktu Shot peening Pada Permukaan Logam Kuningan Terhadap Ketahanan Korosi. Snatif 5 (1)

Wang, H., Li, G., Zhao, X. (2021). Effect of Shot peening Parameters on The Mechanical Properties and Microstructure of Aluminum Alloy. Journal of Materials Processing Technology, 293, 117085.

Xu, W., Zhang, Q., Li, F. (2021). Optimal Shot peening Parameters for Improving Fatigue Life and Mechanical Properties of Aluminum Alloys. Surface and Coatings Technology, 413, 127102.

Zhang, W., Li, J., & Huang, Q. (2023). Optimizing Shot peening Duration for Improved Surface Integrity and Microstructure Refinement. Journal of Surface Engineering and Materials, 29(4), 450-462.

Zhang, Y., Li, X., Wang, J., Li, Y. (2020). Influence of Shot peening on The Mechanical Properties and Surface Integrity of Aluminum Alloys. Materials Science and Engineering A, 781, 139263.

DOI: http://dx.doi.org/10.15578/aj.v6i2.14967